LCM2019 laser engraving machine comes from “open source laser engraving machine” project. As it uses a comparative small power 500mw laser, its market position is a DIY gadget, It is not applicable to batches of cutting materials or production.
Applicable materials for engraving : wood, some plastics, paper, ox horn, leather, pearl wool and so on.
Applicable materials for cutting : paper, slim wood sheet, sticky note and pearl wool.
Inapplicable materials: metal, stone, ceremics, jewellery and jade,reflecting materials , transparent and semi-transparent materials.

If the XYZ can’t  move:

Step 1. Check whether the red Emergency Stop button on the control box is pressed.

Step 2. Check whether the USB cable is connected to the computer normally, and If your computer is a laptop, you must use its power adapter to power the computer.  Plug the USB cable into other USB port of the computer and then try.

Step 3. Turn on the power switch and check whether the stepper motor is self-locking.  If the stepper motor can be turned by hand, it means that the motor is not self-locking.

Step 4. If the stepper motor is NOT self-locking, turn off the power switch and check the fuse (see attached picture)

Step 5. If there is no problem with the fuse, open the control box, turn on the power switch, and check whether the green light of the power module is on (see attached picture). If the light is not on, the power supply module burnt out.

In addition, if you are a Japanese user, please first test whether your input voltage is stable or greater than 100V. It is recommended that you............

Engrave small letters on stainless steel with the X4-800L. The minimum letter width 1mm, height 1.5mm.

For a water-cooled spindle, we need to use correct ways to maintain it.
1. The cooling water, you can choose either tap water or deionized water. Please add a little common antirust into water ( the kind used in water tank of cars is OK).

2. You need to ensure that the spindle runs normally, so that you must avoid the water-cooled spindle lacks water. During operation, please check the surface temperature of the spindle regularly to prevent from a hot spindle.

3. Please measure the temperature of the cooling water periodically, you’d better keep the cooling water within 30 degree centigrade. When the environment temperature is high ( in summer), please use a big-size water tank. When the temperature of the cooling water is rising, you can lower the temperature by adding more water.

4. If you use tap water, please change the water periodically ( change one time in a week)

5. When the temperature in winter is below 5 degree centigrade, please add some anti-freezing solution into the cooling water.

6. If you don’t use the machine for a long time, you must use compressed air to blow out the water in the spindle until there is no water in it............

1. After you installed the batteries, the "battery signal light" of the handle will be on for about 2 seconds.
Then the light is off.

2. Insert the wireless USB receiver into the computer.
Open Mach software, press the “RESET”button of the handle.
At this time the first light on the leftmost  will be on. 

At this moment, if the “RESET” of the Mach3 has not blinked,you can use the handle.
If the the “RESET” of the Mach3 has blinking, press the “RESET”button of the handle once again.

3. Please check whether the “PlugIns” folder of your MACH installation directory has the “ShuttlePro.dll”file.

if you have no "shuttlepro.dll" file,  click here to download it. ............

X4-800L, X6-2200L use new Stepper Drive YOC556,  no longer use M556-GT driver board. ............

Gear Specifications: 70mm*70mm*6mm
Tool type: Common Double-edged milling cutter (blade diameter 3mm)
Cutting speed: 1500mm/min
Layered cutting depth: 1.2mm
Cutting time: 00:04:10

Our old product models : 
3020Z-D52, 
3020Z-4D,
3040Z-D52,
3040Z-4D,
4030Z,
6040Z-S80

June 2013, we published our new series model: X-Series, and a new product ——- X6-1500GT. 
March 2014, we published the second X-series product ——- X4-800.

Now, we prepared more X-series model. here are them names:

X3-300-USB:
‘300’ means 300W spindle . ‘USB’ means this machine use USB connection.

X3-300-LPT:
‘300’ means 300W spindle .’LPT’ means this machine use Parallel connection.

X4-800:
‘800’ means 800W spindle.

X4-800L:
‘800’ means 800W spindle. ‘L’ means this machine equipped with Linear Guide Rails.

X6-1500GT:
‘1500’ means 1500W spindle. ‘GT’ means Great Technology.

Please note that:
For X4-800L and X6-2200L these two models, we have not printed letter "L" on the machine, the machine still marked X4-800 and X6-2200............

Our new version website(omiocnc.com) online on 17th May, 2015. The new website will bring better user experiences for you, more accessible and convenient. It has some following important updates. 

1, Domain 

Old domain:  www.carving-cnc.com
New domain:  www.omiocnc.com

www.carving-cnc.com has been redirected to www.omiocnc.com on 17-05-2015

Note： From now on omiocnc.com is the our only official website. Customers registered on the former carving-cnc.com can direcetly login new website omiocnc.com and manage order. 

2, Brand Logo

Note: From now on the old logo will be no longer used. All our products marked our new logo. If you found the same machines like ours on other websites and they are not been labeled our new logo, those are copies or fakes. Please don’t  buy the copies or fake machines, as they may not working or doesn’t has any warranties. 

3, Service and Support Email
Old email:  [email protected]............