Blog -omiocnc.com

Blog

LCM2019 laser engraving machine comes from “open source laser engraving machine” project. As it uses a comparative small power 500mw laser, its market position is a DIY gadget, It is not applicable to batches of cutting materials or production.
Applicable materials for engraving : wood, some plastics, paper, ox horn, leather, pearl wool and so on.
Applicable materials for cutting : paper, slim wood sheet, sticky note and pearl wool.
Inapplicable materials: metal, stone, ceremics, jewellery and jade,reflecting materials , transparent and semi-transparent materials.

Read More

Engrave small letters on stainless steel with the X4-800L. The minimum letter width 1mm, height 1.5mm.

use omiocnc X4-800L to engrave small letter on stainless steel

use omiocnc X4-800L to engrave small letter on stainless steel

Read More

For a water-cooled spindle, we need to use correct ways to maintain it.
1. The cooling water, you can choose either tap water or deionized water. Please add a little common antirust into water ( the kind used in water tank of cars is OK).

2. You need to ensure that the spindle runs normally, so that you must avoid the water-cooled spindle lacks water. During operation, please check the surface temperature of the spindle regularly to prevent from a hot spindle.

3. Please measure the temperature of the cooling water periodically, you’d better keep the cooling water within 30 degree centigrade. When the environment temperature is high ( in summer), please use a big-size water tank. When the temperature of the cooling water is rising, you can lower the temperature by adding more water.

4. If you use tap water, please change the water periodically ( change one time in a week)

5. When the temperature in winter is below 5 degree centigrade, please add some anti-freezing solution into the cooling water.

6. If you don’t use the machine for a long time, you must use compressed air to blow out the water in the spindle until there is no water in it.

Read More

1. After you installed the batteries, the "battery signal light" of the handle will be on for about 2 seconds.
Then the light is off.

2. Insert the wireless USB receiver into the computer.
Open Mach software, press the “RESET”button of the handle.
At this time the first light on the leftmost  will be on. 

At this moment, if the “RESET” of the Mach3 has not blinked,you can use the handle.
If the the “RESET” of the Mach3 has blinking, press the “RESET”button of the handle once again.

3. Please check whether the “PlugIns” folder of your MACH installation directory has the “ShuttlePro.dll”file.

if you have no "shuttlepro.dll" file,  click here to download it. 

Read More

Product Update

6/18/2015 11:51 AM

16/06/2015,

X4-800L, X6-2200L use new Stepper Drive YOC556,  no longer use M556-GT driver board. 

Read More

Product Model Statement

5/30/2015 2:21 AM

Our old product models :
3020Z-D52,
3020Z-4D,
3040Z-D52,
3040Z-4D,
4030Z,
6040Z-S80


June 2013, we published our new series model: X-Series, and a new product ——- X6-1500GT.
March 2014, we published the second X-series product ——- X4-800.

Now, we prepared more X-series model. here are them names:

X3-300-USB:
‘300’ means 300W spindle . ‘USB’ means this machine use USB connection.

X3-300-LPT:
‘300’ means 300W spindle .’LPT’ means this machine use Parallel connection.

X4-800:
‘800’ means 800W spindle.

X4-800L:
‘800’ means 800W spindle. ‘L’ means this machine equipped with Linear Guide Rails.

X6-1500GT:
‘1500’ means 1500W spindle. ‘GT’ means Great Technology.

X6-2200L:
‘2200’ means 2200W spindle. ‘L’ means this machine equipped with Linear Guide Rails.

Please note that:
For X4-800L and X6-2200L these two models, we have not printed letter "L" on the machine, the machine still marked X4-800 and X6-2200.

Read More

Gear Specifications: 70mm*70mm*6mm
Tool type: Common Double-edged milling cutter (blade diameter 3mm)
Cutting speed: 1500mm/min
Layered cutting depth: 1.2mm
Cutting time: 00:04:10

Read More

Website Updates Statement

5/24/2015 8:43 PM

Our new version website(omiocnc.com) online on 17th May, 2015. The new website will bring better user experiences for you, more accessible and convenient. It has some following important updates. 

1, Domain 

Old domain:  www.carving-cnc.com
New domain:  www.omiocnc.com

www.carving-cnc.com has been redirected to www.omiocnc.com on 17-05-2015

Note: From now on omiocnc.com is the our only official website. Customers registered on the former carving-cnc.com can direcetly login new website omiocnc.com and manage order. 

 

2, Brand Logo
 

Note: From now on the old logo will be no longer used. All our products marked our new logo. If you found the same machines like ours on other websites and they are not been labeled our new logo, those are copies or fakes. Please don’t  buy the copies or fake machines, as they may not working or doesn’t has any warranties. 


3, Service and Support Email

Old email:  [email protected] (no longer used)

New email:  
General contact us:   contactus(at)omiocnc.com
Customer service/support:   service(at)omiocnc.com
Cooperation:  Lance(at)omiocnc.com

If you have any questions, please email us to our new mailbox, we will respond you within 24 hours(except holidays). 

When you visiting on our website, if you find any bugs ( include links bugs, display bugs) please let us know, we will fix it as soon as possible. We hope the brand-new website could give you a better user experience. Thanks. 

 

Read More
per page

Items 25 to 32 of 32 total

Page:
  1. 1
  2. 2
  3. 3
  4. 4